Plumbing Essentials: A Prerequisite for When Installing a Bathtub
Plumbing Essentials: A Prerequisite for When Installing a Bathtub
Blog Article
They are making a number of great points on the subject of A Step-by-Step Guide to Installing a Bathtub in general in this content followed below.
Installing a tub isn't specifically brain surgery, yet it does need strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bath tub with a brand-new one is also a moderately difficult job. If the old bathtub is readily accessible, the project can relocate speedily; if you have to open a wall surface to eliminate the old bathtub and place the brand-new bath tub, the task is a lot harder. In either case, the job is within a home handyman's abilities, although you will certainly need an assistant to vacate the old tub and set in the new one. See to it you have actually certified yourself for the work and are comfortable attempting it. Instead of employing a service provider to take over a halfway-completed project, it is better to think about utilizing one prior to you start. Opportunities are you may need a specialist plumber to make tube connections.
This short article will help you mount a brand-new bathtub in your washroom if you have currently acquired a brand-new tub and also do not need to change the plan of your previous water supply pipes.
Your tools as well as material checklist need to comprise the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your installation, after that the first thing you must do is separate the water system. After doing so, turn on the faucets to drain pipes any kind of water remaining in the system. The process of eliminating the existing taps can be fairly bothersome due to the restricted access that is often the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a towel prepared for the continuing to be water that will originate from the pipelines. When the supply pipelines have actually been removed, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming throughout this process. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Before carrying on to fit the brand-new faucets, contrast the pipeline links on the old taps to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end offers a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin ensuring that the washers are in location in between the faucet and also the sink. Safeguard the faucet in position with the supplier provided backnut. Once the tap is securely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular tap ports. The former type should be linked to the tap finishes initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Bathtub
Using both wooden boards under its feet, put the bathtub in the needed position. The wooden boards are valuable in equally spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 small points.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by examining the level and adjusting the feet on the bathtub up until the level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable tap port to the proper supply pipe by making a compression sign up with; then do the same for the various other tap.
Activate the water as well as examine all joints and also new pipework for leakages and also tighten them if necessary. Fill the bath tub as well as additionally inspect the overflow outlet and also the typical electrical outlet for leaks.
Finally, take care of the bath paneling as defined in the producer's user's manual. Tiling and securing around the bathtub ought to wait till the bathtub has been utilized at least once as this will certainly resolve it right into its last position.
Getting ready for the Installment
Firstly, the supporting framework provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to make certain that if the tap includes a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps system to prevent pressure on the tub.
Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its final setting.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to fracture a stiff seal, triggering the water to penetrate the wall surface between the bath as well as the tiling, causing issues with moisture as well as possible leakages to the ceiling below.
You can select from a variety of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes as well as cartridges, and can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water before securing, to allow for the motion experienced when the bathtub remains in use. The sealant can split rather early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily offered on the marketplace. It is recommended to fit the tiles using waterproof or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate reading up on A Step-by-Step Guide to Installing a Bathtub? Try leaving a remark below. We will be glad to know your responses about this post. We hope that you visit us again soon. If you please take the time to promote this blog entry if you enjoyed it. Kudos for your time. Visit again soon.
Book Appointment Report this page